Soap Making Supplies
Ph: 717-397-4104



facebooktwitterYouTubeSoap Making BlogSoap Making Forum
return to homepage

Acrylic Soap Molds

Soap Making Resource's professional no-line acrylic soap molds are the perfect solution for those of you who are sick and tired of lining your molds with butcher or freezer paper. No more scissors, no more tape, no more money wasted on lining materials!

acrylic soap mold

Click here to purchase the Soap Making Resource acrylic soap mold or keep reading below about the features and benefits of our design. We also have a video further down the page demonstrating this new product!

Update: We now have available the long awaited acrylic no-line tray slab soap mold. This tray mold design offers many new options for styling your soap including the ability to easily embed anything you want into the center of your bar! Many soap makers like to have both a log mold and tray mold as they both have unique advantages when it comes to styling your product. So, feel free to pick up both! Below is a picture of the new acrylic slab soap mold. Click here to check them out now and read about all the cool features!

acrylic soap mold

Think about all the time you will save! This small investment will instantly reduce your mold set up time substantially. Whether you are a soap making hobbyist or a mid-sized handmade soap company, I think these acrylic soap molds will truly benefit your craft. Of course, we also have bulk discounts available for those soap companies or individuals who need more than one mold. Please feel free to take advantage of this savings opportunity!

Want to see the mold in action? Push the "play button" on the following video to see me demonstrate the 5 pound acrylic mold... then keep reading for more important information!

Seen enough? Click here to be taken to the bottom of the page for pricing and to purchase.

Will they leak? These acrylic soap molds have been tested to hold a thinly traced soap without leakage. So no worries! The HDPE bottom fits snugly into the grooves creating a tight seal.

Please note that the soap will not lay on top of the HDPE bottom piece. It is merely there to form a seal as HDPE has a pliability to it that will fit more tightly into its groove than other plastics. A thin acrylic insert is included with your mold that will rest on top of the HDPE. Although this mold will hold a thinly traced soap and is perfect for individuals who make soap from scratch, it is not recommended for very thin melt and pour soap bases as some leaking may occur because melt and pour soap is so incredibly thin.

How do you get the soap out? There are two options for removing your soap from the Soap Making Resource acrylic mold. One option is to completely disassemble your mold (also great for clean up) allowing the log of soap to be removed. The other option is to use the two release holes incorporated into the bottom of the unit and accompanying soap pushers to slide your soap up and out of the mold without having to go through the disassembly process. Please see the pictures below demonstrating the two un-molding options:

acrylic soap mold disassembly methodacrylic soap mold pushing soap out method

Sliding your soap out of the mold using the built in holes and accompanying soap pushers is personally my preferred technique for un-molding.

How does it work? Each mold comes with an acrylic insert that is placed inside the unit. The soap is poured onto this thin piece of acrylic which securely lies on top of the HDPE bottom. After about 24 hours, or once the soap is fully solidified you will place the soap pushers into the bottom holes and apply pressure to slide the soap out of the mold.

Tip: A quick 5 - 10 minute trip to the oven at 170 degrees Fahrenheit, just before you un-mold your soap, will warm your batch just enough so that the solid log will slip right out of the mold with almost no pressure at all. Very easy and convenient! Alternately, you can put the entire batch of soap in your freezer and as it thaws your soap will release without a problem. Even your stickiest soap recipes will come out of this mold... so no worries!

acrylic soap mold in oven acrylic soap mold in freezer

It's easy as that and your soap will emerge without a flaw!

Finally, once the log of soap is completely pushed out of the mold, simply remove the thin acrylic sheet from the bottom of the soap and cut your log into bars.

No unbolting and no complications! Our thought was that simple is best!

Note: Keep in mind that the soap pushers are pushing on the plastic insert piece and not on the soap itself, avoiding any and all damage to your product.

With the integrated release holes and soap pushers, both original Soap Making Resource mold features, you will save time as you won't have to disassemble the mold and you will also have 100% perfect sides as you won't pull away any of the soap during disassembly which could damage your finished product.

Click here to view size options, pricing and to purchase.

This option to push out your soap without disassembling your mold is also perfect for those sticky batches that may make pulling the acrylic away from your soap a bit more difficult.

The second option for un-molding your soap is to disassemble the mold completely allowing the log to be removed. This can be done easily with many batches, once heat or cold is added, but some stickier soap recipes may present problems as it could be difficult to pull the plastic away from the soap without damaging the sides.

Note: As mentioned above, our acrylic soap molds give you an alternative un-molding option via the release holes and soap pushers that will make removing even the stickiest soaps without any damage a complete breeze. This is one reason why I so strongly feel that the Soap Making Resource no-line acrylic soap mold is such a wonderful investment and unique product.

The assembly and disassembly feature not only will allow you a way to remove your soap if you decide to not use the soap pushers, but it also makes it very easy to clean your mold once your batch is finished. Simply take apart the mold, put the pieces in a sink filled with warm water, and after a few hours, wipe all parts clean. Easy as pie!

acrylic soap mold in sink

There are two sizes available for the Soap Making Resource acrylic soap molds. The small size will make 2 pounds of soap producing seven bars if you cut them one inch thick, and the large size will make 5 pounds of soap producing sixteen one inch thick bars. Of course, you can cut your soaps into any thickness that you desire.

Making bigger batches? There are discounts for purchasing more than one mold to accommodate a larger batch size. If you're making a 10 pound batch of soap, you can get two of the 5 pound molds. If you're making a 20 pound batch, you can get four of the 5 pound molds, etc.

Furthermore, custom sizes are available upon request. This is especially useful if you have a bar size requirement that needs to be met. For more information about ordering custom acrylic soap molds, please click here.


2 Pound acrylic soap mold (includes lid, acrylic insert and soap pushers)

2 pound acrylic soap mold

The 2 pound acrylic soap molds have interior dimensions of 3.5 inches wide by 2.75 inches high by 7 inches long. They will produce 2 pounds of soap.

1 mold: $69.00 Sale: $64.00
2 molds: $135.00 Sale: $125.00
3 molds: $202.00 Sale: $185.00
4 molds: $269.00 Sale: $245.00 (Free delivery on all items in cart)
5 molds: $335.00 Sale: $305.00 (Free delivery on all items in cart)
6 molds: $400.00 Sale: $365.00 (Free delivery on all items in cart)
10 molds: $665.00 Sale: $605.00 (Free delivery on all items in cart)
20 molds (bulk): $1283.40 Sale: $1190.40 (Free delivery on all items in cart)

Acrylic Soap Mold (2 Pound) - Choose Quantity:

Need a bigger mold? Click here to see the 5 pound acrylic soap mold.


5 Pound acrylic soap mold (includes lid, acrylic insert and soap pushers)

5 pound acrylic soap mold

The 5 pound acrylic soap molds have interior dimensions of 3.5 inches wide by 2.75 inches high by 16 inches long. They will produce 5 pounds of soap.

1 mold: $99.00 Sale: $89.00
2 molds: $195.00 Sale: $175.50
3 molds: $292.00 Sale: $262.80 (Free delivery on all items in cart)
4 molds: $389.00 Sale: $350.10 (Free delivery on all items in cart)
5 molds: $485.00 Sale: $436.50 (Free delivery on all items in cart)
6 molds: $580.00 Sale: $522.00 (Free delivery on all items in cart)
10 molds: $965.00 Sale: $868.50 (Free delivery on all items in cart)
20 molds (bulk): $1841.40 Sale: $1657.26 (Free delivery on all items in cart)

Acrylic Soap Mold (5 Pound) - Choose Quantity:

Need a smaller mold? Click here to see the 2 pound acrylic soap mold.

Thank you very much for taking a look at the Soap Making Resource no-line acrylic soap molds. Please don't forget that if you are searching for a different size then what is offered as stock, we do manufacture custom molds that will be built according to your specific dimensions. Click here for a custom acrylic soap mold quote.

If you have any questions, please feel free to use the contact form to send us a message or call 717-875-8670. We are happy to help!



Return from acrylic soap molds to the soap making resource home page.
Soap Making Supplies Blog
Click to Contact Us

Shopping Cart:

View Cart

Free Grab Bag

Free Delivery on
Orders $200 or more...

*contiguous USA only
*excludes 5 gallon oil pails


Additional 5% off on
Orders of $500 or more...

* This additional 5% discount will be processed manually by our staff after you place your order.


Need help ordering?
Call:
717-397-4104
Open: 8am - 6pm EST
Online Ordering: 24/7

Web Ecommerce

Don't Forget to sign up for the Soap Making Resource Newsletter!

Soap Making Resource
Promos and News:

_____________________

Free Delivery on Orders
$200 or more!
*contiguous USA only



Enjoy This Site?
Then why not use the button below, to add us to your favorite bookmarking service?

[?] Subscribe To This Site

XML RSS
follow us in feedly
Add to My Yahoo!
Add to My MSN

Homepage

All content is for informational purposes only.

Copyright© 2008-2014.